crwdns2933423:0crwdne2933423:0

Kenmore Model 110 Clutch Replacement

crwdns2942213:0crwdne2942213:0

  1. Kenmore Model 110 Clutch Replacement, Transmission Clutch: crwdns2935265:01crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Kenmore Model 110 Clutch Replacement, Transmission Clutch: crwdns2935265:01crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • Unplug the washing machine.

    • Turn both the hot and cold water supply lines off.

  2. Kenmore Model 110 Clutch Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Disconnect the supply hoses using channel lock pliers. Use the towel to catch any water that may spill out.

  3. Kenmore Model 110 Clutch Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Use the channel lock pliers to remove tension on the hose spring clamp and pull the drain line from the washer.

    • Water will come out when hose is disconnected.

  4. Kenmore Model 110 Clutch Replacement: crwdns2935265:04crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:04crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • Pinch the plastic tabs with the needle nose pliers and push through the metal back panel.

  5. Kenmore Model 110 Clutch Replacement: crwdns2935265:05crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Pull up the control panel located on top of the washer machine.

  6. Kenmore Model 110 Clutch Replacement: crwdns2935265:06crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Lift the plastic tab on the timer wiring harness connector and pull from the timer.

  7. Kenmore Model 110 Clutch Replacement: crwdns2935265:07crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:07crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • Disconnect the hose and wiring harness from water level control.

  8. Kenmore Model 110 Clutch Replacement: crwdns2935265:08crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:08crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:08crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
    • Push tab and remove the connector that is next to the water level control on the inside of the control panel.

    • Pull the connector from the door safety switch located on the main body of the washing machine top.

    • Disconnect the green wire ground point inside the control panel with the ratchet and a 1/4 inch socket.

  9. Kenmore Model 110 Clutch Replacement: crwdns2935265:09crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Use the flat head screwdriver to pry out clips on left and right side on top of the machine where the control panel was.

  10. Kenmore Model 110 Clutch Replacement: crwdns2935265:010crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:010crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:010crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
    • Pull the hood gently from the front to separate from the base, leaving the tub, motor, and transmission exposed.

    • Carefully tilt the washer and set it on the back panel

  11. Kenmore Model 110 Clutch Replacement: crwdns2935265:011crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:011crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • Remove the pump retaining clips.

    • Leave the pump hoses attached and move the pump aside.

  12. Kenmore Model 110 Clutch Replacement: crwdns2935265:012crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:012crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • Lift the tab and remove the motor wiring harness connector.

    • Remove the plastic clip from the transmission housing.

  13. Kenmore Model 110 Clutch Replacement: crwdns2935265:013crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:013crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • Remove the motor retaining clip screws with the ratchet and a 1/4 inch socket.

    • Use the flat head screw driver to pry retaining clips off of motor.

  14. Kenmore Model 110 Clutch Replacement: crwdns2935265:014crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:014crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • Separate the motor from the transmission.

    • Be sure to check the rubber motor coupling while it is apart. The motor and the transmission will have a plastic piece with three prongs that fit into the rubber coupling. Check to make sure plastic prongs have not broken and the rubber coupling is not cracked.

    • If the motor coupling is cracked or broken it will need to be replaced.

  15. Kenmore Model 110 Clutch Replacement: crwdns2935265:015crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:015crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:015crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
    • Inside the wash tank, use the flat head screw driver to pop cap off of the agitator.

    • Remove the transmission shaft nut with the ratchet and a 7/16 inch socket.

    • Remove the agitator by pulling it from the transmission shaft.

  16. Kenmore Model 110 Clutch Replacement: crwdns2935265:016crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:016crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • On the bottom of the machine, remove the 3 bolts that hold the transmission in place with the ratchet and a 3/8 inch socket.

    • Gently pull the transmission out of the washer.

  17. Kenmore Model 110 Clutch Replacement: crwdns2935265:017crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:017crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Kenmore Model 110 Clutch Replacement: crwdns2935265:017crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
    • Remove the metal washer from the transmission shaft.

    • Pry the retaining clip from the transmission shaft with the flat head screw driver.

    • Pry the spring clip from the clutch with the flat head screw driver.

  18. Kenmore Model 110 Clutch Replacement: crwdns2935265:018crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Remove the clutch.

crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2935229:04crwdne2935229:0

Jonathan Beach

crwdns2935283:001/30/18crwdne2935283:0

404 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2915084:0crwdne2915084:0

Eastern Washington University, Team S27-G1, Crane Winter 2018 crwdns2935289:0Eastern Washington University, Team S27-G1, Crane Winter 2018crwdne2935289:0

EWU-CRANE-W18S27G1

crwdns2931471:04crwdne2931471:0

crwdns2935297:05crwdne2935297:0

crwdns2944067:02crwdne2944067:0

My Kenmore washer is as same as this one, but now the agitator works, but it does not spin. So far I reached step 14, did not find anything wrong, which parts could be the problem? Clutch? Thanks

Harry Song - crwdns2934203:0crwdne2934203:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 9

crwdns2936753:07crwdne2936753:0 60

crwdns2936753:030crwdne2936753:0 255

crwdns2942667:0crwdne2942667:0 13,087