crwdns2915892:0crwdne2915892:0
This guide demonstrates how to replace the camera's speaker.
crwdns2942213:0crwdne2942213:0
-
-
Turn off camera by firmly pressing the power button that is located on the top of the camera near the selector dial.
-
-
-
Press thumb firmly on battery door and slide it in the direction of the arrow.
-
Lift thumb allowing the door to swing open.
-
-
crwdns2935267:0crwdne2935267:0Anti-Static Wrist Strap$7.95
-
Before removing back cover, it is advisable to use an anti-static wrist strap to prevent damage to electronics.
-
-
-
Turn the camera off by firmly pressing the power button located on top of the camera.
-
-
-
Locate the 7 screws holding the back cover on.
-
Three screws are located on the bottom of the camera.
-
Two screws are located on the side shown in the photograph.
-
Two final screws are located on the opposite side shown in the photograph.
-
-
-
Remove all 7 screws:
-
Hold the camera firmly with one hand so that you can still see a screw.
-
Place the Philips 00(Found here)screwdriver into the screw.
-
Turn the screwdriver to the left until it is free.
-
Repeat for the remaining screws.
-
-
-
Use plastic opening tools to slightly open the side of the case.
-
Insert a plastic opening tool and apply pressure to the internal three tabs at the top.
-
The first two are near the words "3X Optical Zoom".
-
The third is near the shutter button.
-
-
-
Gently pull apart the back cover from the rest of the camera.
-
Make sure there are no more screws or tabs keeping the cover on.
-
Use the plastic opening tool to separate any sides still closely connected.
-
-
-
-
Open the battery door.
-
Press thumb firmly on battery door and slide it in the direction of the arrow.
-
Lift thumb allowing the door to swing open.
-
-
-
Use the plastic opening tool to lift the casing around the shutter button.
-
Gently remove the front cover from the device.
-
-
-
To discharge the capacitor follow this guide.
-
-
-
Locate the exposed portion of the LCD screen.
-
Use a wedge to free the LCD screen from the medal housing.
-
-
-
Remove the screw at the upper right corner of the metal housing.
-
-
-
Locate the 2 solder joints holding down the medal housing.
-
Remove the solder.
-
Place wick on solder.
-
Place solder iron on wick
-
-
-
Peel back the black tape from the metal housing.
-
Lift the metal housing from the left so that it hinges on its right side.
-
-
-
Locate black tab holding the LCD screen connector in the port.
-
Use wedge or fingernail to lift the black tab.
-
Pull the the LCD screen connector out of the port.
-
-
-
Remove the medal housing from the logic board by carefully peeling the yellow tape off of the metal housing.
-
-
-
Locate the 2 screws on the yellow tape.
-
Remove the 2 screws.
-
Remove the yellow tape.
-
-
-
Locate the 2 solder joints near the shutter button.
-
Remove the solder on both joints with the wick and soldering iron in the same manner as Step 11.
-
-
-
Turn the camera over.
-
Remove the screw holding the small green board.
-
Lift the small green board.
-
-
-
Desolder the remaining 20 solder joints connecting the logic board to the camera.
-
-
-
Locate the black tab holding the yellow cable in place.
-
Use a plastic opening tool or fingernail to lift the black tab.
-
Pull the yellow cable from the port.
-
-
-
Use a plastic opening tool to lift the board from the camera.
-
Continue to remove the board completely.
-
-
-
Carefully pull the red and black wires located on the side of the camera connected to the speaker.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2915084:0crwdne2915084:0
Cal Poly, Team 24-22, Regan Spring 2010 crwdns2935289:0Cal Poly, Team 24-22, Regan Spring 2010crwdne2935289:0
CPSU-REGAN-S10S24G22
crwdns2931471:04crwdne2931471:0
crwdns2935297:022crwdne2935297:0
