crwdns2931653:01crwdne2931653:0 Remove label to access screws

• Peel back the "ELECTRONIC KITCHEN SCALE" label to reveal two screws underneath.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:02crwdne2931653:0

• Use a #2 Phillips screwdriver to remove the two screws.
• These screws are very tight and prone to strip.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:03crwdne2931653:0
• Remove the four screws holding the top veneer panel to the base.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:04crwdne2931653:0
• Remove the top veneer panel. It should come off without any force.
• There are two small plastic clips on the edge below the screen, which must be inserted correctly during reassembly.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:05crwdne2931653:0
• Remove the screw holding the PCB and screen in place using a #1 Phillips screwdriver.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:06crwdne2931653:0
• Remove the PCB and screen assembly.
• The buttons should also lift up with the rest of the PCB/screen assembly.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:07crwdne2931653:0
• Use a #1 Phillips screwdriver to remove the four screws holding the load cell mount to the base.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:08crwdne2931653:0
• Remove the two screws holding the load cell to the bracket using a #2 Phillips screwdriver.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:09crwdne2931653:0
• Separate the bracket from the load cell.
• Be careful not to lose the spacer plate.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0

crwdns2942557:0crwdne2942557:0

crwdns2942955:0crwdne2942955:0

<iframe id="dozuki-embed-137064" src="https://ts.ifixit.com/Guide/embed/137064/full" width="800" allowfullscreen frameborder="0"></iframe> <script>window.addEventListener("message",function(a){var b=document.getElementById("dozuki-embed-137064"),c=a.data[0],d=a.data[1];switch(c){case"setHeight":b.style.height=d+"px"}},!1);</script> <iframe src="https://ts.ifixit.com/Guide/embed/137064" width="800" height="584" allowfullscreen frameborder="0"></iframe>

crwdns2852917:0crwdne2852917:0