crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

Dopo Double Power 7 Battery Replacement

crwdns2915892:0crwdne2915892:0

Skills you will need to be familiar with are soldering. Besides a new battery, you will also need access to a soldering kit.

crwdns2942213:0crwdne2942213:0

  1. Dopo Double Power 7 Battery Replacement, Rear Panel: crwdns2935265:01crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • The rear panel is secured to the front case and can simply be pried apart without damage.

    crwdns2913378:0crwdne2913378:0

  2. Dopo Double Power 7 Battery Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Carefully, wedge the plastic opening tool in-between the seam that separates both halves of the tablet.

    crwdns2913378:0crwdne2913378:0

  3. Dopo Double Power 7 Battery Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Run the plastic opening tool along the seam looking for the clips and lift up on the rear panel.

    crwdns2913378:0crwdne2913378:0

  5. Dopo Double Power 7 Battery Replacement: crwdns2935265:04crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • The rear panel should come completely off.

    crwdns2913378:0crwdne2913378:0

  6. Dopo Double Power 7 Battery Replacement, Battery: crwdns2935265:05crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Cut only the red and black wires attaching the battery to the motherboard.

    • Be sure to remove any remaining wire attached to the motherboard.

    crwdns2913378:0crwdne2913378:0

  7. Dopo Double Power 7 Battery Replacement: crwdns2935265:06crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Using a metal spudger, carefully pry the battery away from the digitizer.

    • Be careful to not damage the battery. This could result in injury.

    crwdns2913378:0crwdne2913378:0

  8. Dopo Double Power 7 Battery Replacement: crwdns2935265:07crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Using wire strippers, strip the ends of the red and black wires connected to the the new battery back about a 1/8".

    • Twist the strands of the spliced wire together.

    • Using a soldering iron, apply heat to one bare wire connections you have just made.

    • When the connection is hot enough melt solder on the opposite side of the wire to the iron as shown in the image. Do not melt to much solder.

    • Once connection is made wait for it to cool off and gently pull each side of the wire to test durability.

    • Repeat this process with the other wire.

    • If you do not have access to a soldering iron, leave the old battery wires attached to the motherboard and simply splice the new battery's wires to them.

    • This video provides basic instructions for splicing wires using crimping and heat shrink technique.

    crwdns2913378:0crwdne2913378:0
crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2935227:0crwdne2935227:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:03crwdnd2935293:0crwdne2935293:0

mike pelosi

crwdns2935283:010/30/15crwdne2935283:0

682 crwdns2915208:0crwdne2915208:0

crwdns2935297:06crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 12

crwdns2935301:09crwdne2935301:0

crwdns2915084:0crwdne2915084:0

UMass Dartmouth, Team 1-2, Miles Fall 2015 crwdns2935289:0UMass Dartmouth, Team 1-2, Miles Fall 2015crwdne2935289:0

UMASSD-MILES-F15S1G2

crwdns2931471:04crwdne2931471:0

crwdns2935297:012crwdne2935297:0

crwdns2944067:00crwdne2944067:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 1

crwdns2936753:07crwdne2936753:0 4

crwdns2936753:030crwdne2936753:0 9

crwdns2942667:0crwdne2942667:0 999