crwdns2894164:0crwdne2894164:0

crwdns2860947:0crwdne2860947:0

crwdns2890040:0crwdne2890040:0

  1. Disassembling Marshall MS-2 Partner Circuit Board, Disassembling Marshall MS-2 Micro Amp Case Disassembly: step 1, image 1 of 1
    • First be sure to turn the power switch to the off position.

    • Do this by turning the leftmost knob counter-clockwise as until the line points to "off."

    To turn the device off, turn the rightmost knob counterclockwise, not the leftmost one (which controls the volume).

    Célestin Taramarcaz - crwdns2853112:0crwdne2853112:0

  2. Disassembling Marshall MS-2 Partner Circuit Board: step 2, image 1 of 3 Disassembling Marshall MS-2 Partner Circuit Board: step 2, image 2 of 3 Disassembling Marshall MS-2 Partner Circuit Board: step 2, image 3 of 3
    • Now remove the battery.

    • On the back of the device locate the battery cover.

    • Remove it by pushing down on the clip.

    • Then pull the piece of fabric until the battery comes out.

  3. Disassembling Marshall MS-2 Partner Circuit Board: step 3, image 1 of 2 Disassembling Marshall MS-2 Partner Circuit Board: step 3, image 2 of 2
    • Use the long, skinny phillips head screwdriver to remove the 4 7/16" screws on the back of the device in the four corners.

    • Once unscrewed, do not try to take each screw out. Move to next step once all screwed have been unscrewed.

  4. Disassembling Marshall MS-2 Partner Circuit Board: step 4, image 1 of 1
    • Now pull the back panel off and place it down as shown. Pull the panel straight up so you do not lose the screws.

  5. Disassembling Marshall MS-2 Partner Circuit Board, Partner Circuit Board: step 5, image 1 of 2 Disassembling Marshall MS-2 Partner Circuit Board, Partner Circuit Board: step 5, image 2 of 2
    • Use a 9/16" socket to remove the nut around the headphone jack. Be careful to not lose the washer.

  6. Disassembling Marshall MS-2 Partner Circuit Board: step 6, image 1 of 1
    • Remove the 7/16" phillips head screw.

  7. Disassembling Marshall MS-2 Partner Circuit Board: step 7, image 1 of 1
    • Grab the headphone jack from inside the case and pull it toward the speaker until you can fully remove it from the device.

crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2878426:02crwdne2878426:0

MacKinley

crwdns2886885:022/10/2013crwdne2886885:0

765 crwdns2915208:0crwdne2915208:0

crwdns2886889:05crwdne2886889:0

crwdns2915084:0crwdne2915084:0

University of Maryland, Team 1-1, Shastany Fall 2013 crwdns2886886:0University of Maryland, Team 1-1, Shastany Fall 2013crwdne2886886:0

UMD-SHASTANY-F13S1G1

crwdns2858115:03crwdne2858115:0

crwdns2886889:05crwdne2886889:0

crwdns2917034:0crwdne2917034:0

There Is a toroidal transformer inside ?

Jack redmond - crwdns2853112:0crwdne2853112:0

crwdns2917038:0crwdne2917038:0

crwdns2894754:0crwdne2894754:0:

crwdns2894766:024crwdne2894766:0 1

crwdns2894768:07crwdne2894768:0 3

crwdns2894768:030crwdne2894768:0 11

crwdns2894770:0crwdne2894770:0 1,645