crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Disassembling 8BitDo Pro 2 Wired Joystick Board

crwdns2915892:0crwdne2915892:0

Follow this guide to remove the board that contains both joystick modules. Removing the board let's you solder new modules or clean them.

crwdns2942213:0crwdne2942213:0

  1. Disassembling 8BitDo Pro 2 Wired Joystick Board, Remove R2 and L2 pads: crwdns2935265:01crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Disassembling 8BitDo Pro 2 Wired Joystick Board, Remove R2 and L2 pads: crwdns2935265:01crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Remove both pads by pushing them up.

    crwdns2913378:0crwdne2913378:0

  2. Disassembling 8BitDo Pro 2 Wired Joystick Board, Remove T6 Screws: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Remove both Torx T6 screws from the back.

    crwdns2913378:0crwdne2913378:0

  4. Disassembling 8BitDo Pro 2 Wired Joystick Board, Open the controller: crwdns2935265:03crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Disassembling 8BitDo Pro 2 Wired Joystick Board, Open the controller: crwdns2935265:03crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Disassembling 8BitDo Pro 2 Wired Joystick Board, Open the controller: crwdns2935265:03crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

    • With an opening pick, detach the seven clips holding the faceplate. Start from the sides, towards the bottom.

    • Detach the remaining clips by carefully raising the faceplate away from the clips.

    • A flex cable joins both plates.

    • Move the faceplate to the side.

    crwdns2913378:0crwdne2913378:0

  5. Disassembling 8BitDo Pro 2 Wired Joystick Board, Remove the flex cable: crwdns2935265:04crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Push the sides of the connector away from it to free the cable.

    crwdns2913378:0crwdne2913378:0

  6. Disassembling 8BitDo Pro 2 Wired Joystick Board, Remove the #0 screws: crwdns2935265:05crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Remove the 8 screws using a Phillips #0 screwdriver.

    • You can remove the joystick caps by lifting them.

    crwdns2913378:0crwdne2913378:0

  7. Disassembling 8BitDo Pro 2 Wired Joystick Board, Remove the board: crwdns2935265:06crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Disassembling 8BitDo Pro 2 Wired Joystick Board, Remove the board: crwdns2935265:06crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Slowly lift the board from the controller. Make sure to lift both rumble motors as well.

    crwdns2913378:0crwdne2913378:0
crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2862417:0crwdne2862417:0

crwdns2935291:0crwdnd2935291:01crwdnd2935291:0crwdne2935291:0

Adrián

crwdns2935283:001/22/23crwdne2935283:0

138 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2918514:0crwdne2918514:0: 4

crwdns2935299:0crwdne2935299:0

crwdns2947412:00crwdne2947412:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 2

crwdns2936753:07crwdne2936753:0 7

crwdns2936753:030crwdne2936753:0 27

crwdns2942667:0crwdne2942667:0 49