crwdns2894164:0crwdne2894164:0

crwdns2915892:0crwdne2915892:0

How to remove the battery of a Dell XPS 13 7390 laptop. The images and information in this guide were taken from this computer's service manual.

  1. Dell XPS 13 7390 Battery Replacement, Removing the base cover: step 1, image 1 of 3 Dell XPS 13 7390 Battery Replacement, Removing the base cover: step 1, image 2 of 3 Dell XPS 13 7390 Battery Replacement, Removing the base cover: step 1, image 3 of 3
    • Remove the eight screws (M2x3, Torx) that secure the base cover to the palm-rest assembly

    • With the computer face-down, open the computer at an angle.

    • Using a plastic scribe, pry the base cover from the palm-rest assembly

    • Moving the base cover from left to right, release the clips securing the base cover to the palm-rest assembly.

    • Lift the base cover from the palm-rest assembly.

  2. Dell XPS 13 7390 Battery Replacement, Remove the old battery: step 2, image 1 of 2 Dell XPS 13 7390 Battery Replacement, Remove the old battery: step 2, image 2 of 2
    • Ensure that the battery cable is disconnected from the system board.

    • Remove the four screws (M2x2) that secure the battery to the palm-rest assembly

    • Remove the screw (M1.6x4) that secures the battery to the palm-rest assembly.

    • Lift the battery off the palm-rest assembly.

    • Turn the computer over, open the display, and press the power button for about 5 seconds to ground the computer.

  3. Dell XPS 13 7390 Battery Replacement, Insert the new battery: step 3, image 1 of 1
    • Align the screw holes on the battery with the screw holes on the palm-rest assembly.

    • Replace the four screws (M2x2) that secure the battery to the palm-rest assembly.

    • Replace the screw (M1.6x4) that secures the battery to the palm-rest assembly

  4. Dell XPS 13 7390 Battery Replacement, Reattach base case: step 4, image 1 of 2 Dell XPS 13 7390 Battery Replacement, Reattach base case: step 4, image 2 of 2
    • Align the screw holes on the base cover with the screw holes on the palm-rest assembly and slide in the base cover into place.

    • Replace the eight screws (M2x3, Torx) that secure the base cover to the palm-rest assembly

crwdns2915888:0crwdne2915888:0

Congratulations, you’re all done!

Max Kletskov

crwdns2886885:022/04/2020crwdne2886885:0

37,348 crwdns2915208:0crwdne2915208:0

crwdns2886889:015crwdne2886889:0

crwdns2915084:0crwdne2915084:0

iFixit crwdns2886886:0iFixitcrwdne2886886:0

Community

crwdns2858115:0148crwdne2858115:0

crwdns2886889:015,461crwdne2886889:0

crwdns2917036:00crwdne2917036:0

crwdns2917038:0crwdne2917038:0

crwdns2894754:0crwdne2894754:0:

crwdns2894766:024crwdne2894766:0 6

crwdns2894768:07crwdne2894768:0 46

crwdns2894768:030crwdne2894768:0 202

crwdns2894770:0crwdne2894770:0 772