crwdns2915892:0crwdne2915892:0
This guide will show you how to access and replace the heart of this camcorder, the central capturing unit assembly.
crwdns2942213:0crwdne2942213:0
- 
   
   - 
                     
            Remove the strap by undoing the Velcro and pulling it through the thread points. 
- 
                     
            Remove the external battery pack by pressing down on the slide release and sliding it out. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the three 5mm Phillips #000 screws on the bottom of the device. 
 
- 
                     
            
- 
   
   - 
                     
            On the side of the device, remove the following Phillips #000 screws: 
- 
                     
            One 3mm screw 
- 
                     
            One 5mm screw 
 
- 
                     
            
- 
   
   - 
                     
            Remove the panel opposite the display by pulling up perpendicular to the side. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the 4mm Phillips #000 screw that was exposed after taking off the side panel. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the three 4mm Phillips #000 screws shown. 
 
- 
                     
            
- 
   
   crwdns2935267:0crwdne2935267:0Tweezers$4.99- 
                     
            Using tweezers, disconnect this ribbon cable by pulling straight out. 
 
- 
                     
            
- 
   
   - 
                     
            Repeat step seven (7) for the remaining three wires shown. 
 
- 
                     
            
- 
                     
                                                
- 
   
   - 
                     
            Grasp the top of the camera and pull straight up to remove the top panel. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the 5mm Phillips #000 screw on top of the inner case. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the two 5mm Phillips #000 screws near the display panel. 
 
- 
                     
            
- 
   
   - 
                     
            Disconnect the small bundled cable connector on the side of the lens cover by pulling it straight out. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the lens cover by pulling straight away from the body. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the three 6mm Phillips #000 screws shown. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the lens by pulling straight away from the main body. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the two 3mm Phillips #000 screws. 
- 
                     
            Remove the 4mm Phillips #000 screw. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the 4mm Phillips #000 screw at the bottom of the camera. 
 
- 
                     
            
- 
   
   - 
                     
            Place the spudger under the tab shown. 
- 
                     
            While prying the tab up with the spudger, pull the case away. 
 
- 
                     
            
- 
   
   - 
                     
            Using a spudger, disconnect the ribbon cable connector from the PC board shown in the picture. 
 
- 
                     
            
- 
   
   crwdns2935267:0crwdne2935267:0Tweezers$4.99- 
                     
            Using tweezers, disconnect the ribbon cable shown in the picture by pulling straight out. 
 
- 
                     
            
- 
   
   - 
                     
            Using a spudger, gently pry up the top tab on the ZIF connector. The wire will now disconnect with no force needed. 
 
- 
                     
            
- 
   
   - 
                     
            Using your fingers, firmly grasp both ends of the capturing device and gently pull the assembly straight out. 
 
- 
                     
            
To reassemble the central capturing unit, follow these instructions in reverse order.
To reassemble the central capturing unit, follow these instructions in reverse order.
crwdns2947410:01crwdne2947410:0
thank you for helping me and i am really grateful for your assistance.
