crwdns2915892:0crwdne2915892:0
If the playback on the camcorder is not producing any sound, then the problem lies in the microphone. This can be caused by a broken wire, or debris in the microphone.
crwdns2942213:0crwdne2942213:0
- 
   
   - 
                     
            On the right side of the camcorder remove the grip belt. 
 
- 
                     
            
- 
   
   - 
                     
            On the bottom of the battery hold the battery release switch. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the battery slowly away from the camcorder. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the two 8mm Philips #000 screws on the side where the grip belt was located on. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the two 4mm Philips #000 head screws from the bottom of the camcorder. 
- 
                     
            A hidden 4mm Philips #000 screw is shown under the black plug shown. 
 
- 
                     
            
- 
   
   - 
                     
            Near the LCD screen, remove the three 7mm Philips #000 screws in the picture shown. 
 
- 
                     
            
- 
                     
                                                
- 
   
   - 
                     
            Carefully place the camcorder where the inside of the device is facing upwards and remove the 3mm Philips #000 screw shown. 
 
- 
                     
            
- 
   
   - 
                     
            Using the spudger, pull the tab shown to start removing the ribbon cable. 
 
- 
                     
            
- 
   
   - 
                     
            Using the Spudger, carefully remove the two ribbon cables that are connected to the top of the device. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the two 5mm Phillips #000 screws near the LCD screen. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the single 5mm Phillips #000 screw located on the top of the camera near the lens cover. 
 
- 
                     
            
- 
   
   - 
                     
            Unplug the cord connecting the camera to the lens cover. Grip the white plug near the port and pull it out. 
 
- 
                     
            
- 
   
   - 
                     
            The lens cover is detached from the camera and can now be removed. 
- 
                     
            Repair or replace damaged components in the lens cover. 
- 
                     
            Ensure lens cover mechanism is free of debris. 
 
- 
                     
            
- 
   
   - 
                     
            Remove one 5mm Philips #000 screw from the lens cap. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the lens cover and place in a safe place. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the one 3mm Philips #000 screw that holds the microphone in place. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the metal plate that holds the microphone. 
 
- 
                     
            
- 
   
   - 
                     
            Remove the defective microphone out of the lens cap. 
 
- 
                     
            
- 
   
   - 
                     
            Insert the new microphone in the same place. 
 
- 
                     
            
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935227:0crwdne2935227:0
