crwdns2915892:0crwdne2915892:0
This guide will walk you through the process of removing the interior rear frame in a Canon PowerShot SD 600.
crwdns2942213:0crwdne2942213:0
-
-
Turn the camera over so that the battery compartment is visible. The compartment should read "Card/Batt. Open".
-
Open the compartment.
-
Lightly push the compartment lid down and outward. The arrow next to "Card/Batt. Open" indicates the direction you should be pushing.
-
-
-
Once the lid is open, the battery and SD card compartments become visible.
-
Notice the red tab on the right side of the battery.
-
Slide this tab off the battery.
-
The battery is now free to slide out of the compartment.
-
-
-
To remove the SD card push it down and it will eject out. (SD card not shown)
-
-
-
There are six 3mm exterior screws that will need to be removed in order to remove the exterior frame.
-
Two screws near the tripod mount on the underside of the camera.
-
Two screws on the camera left hand side (the face with nothing but screws on it).
-
Two screws on the camera right hand side, by the wrist strap attachment.
-
Remove the screws using the screwdriver.
-
-
-
Remove the wrist strap attachment.
-
Use the spudger to pry it open.
-
Remove the small circular cover underneath the wrist strap attachment.
-
-
-
Carefully pull apart the two parts of the exterior frame.
-
Use the spudger to pry apart the two frame components.
-
Once disconnected, the two parts of the frame can be easily separated by using your fingers.
-
The rear frame should be removed first.
-
There should be an O-ring on the front face of the camera. Ensure to keep the O-ring with the front part of the frame.
-
-
-
-
The power and shutter buttons are located on the top of the camera and are removed as a single unit.
-
Use the spudger to lift the power/shutter buttons from the camera.
-
-
-
Disconnect the cable that connects the screen to the front motherboard.
-
Using a spudger, unsnap the jawbone connector that holds the cable in
-
Gently pull the cable out using the spudger.
-
-
-
At the back of the camera, there are four 2.5mm screws that will need to be removed in order for the screen to pull off.
-
One at the top of the camera that is connected to a bracket that secures the screen.
-
Two on the back of the camera,near the speaker.
-
One hidden behind the bracket.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Gently lift the screen and pull it apart from the camera, taking care to unslot the screen brackets from the tabs on the bottom and left side of the camera.
-
Do not pull too hard on the screen as there is still another delicate cable running from the screen to the rear board of the camera.
-
Gently pull the wide ribbon (shown in an earlier step) cable from the front of the camera to the back using tweezers.
-
-
-
The screen is now connected only by a small cable that runs to the rear board of the camera. Using tweezers, slowly pull the cable out of the connector.
-
For best results, grip the cable as close to the connector as possible.
-
The screen should now be separate from the camera body. Be careful not to harm the connectors on the lens so it will reconnect successfully.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
First it is necessary to remove the ribbon cable connecting the control board to the [green] rear accessory board on the camera.
-
This is done by unsnapping the jawbone connector and gently pulling the cable out with tweezers or the spudger.
-
-
-
Using the spudger, gently push up the board from the pins underneath it.
-
Follow the board up and around the camera, gently unseating the board and cables.
-
The speaker will still be connected to the board via two small power wires. Use the tweezers to pull and unplug the power connector from the main rear accessory board.
-
-
-
Grip the top control board with the tweezers and gently pull up to unseat it from the placement pins it sits on.
-
If need be, use the spudger to gently pry out the optical viewfinder.
-
-
-
The rear control board should now be completely separate from the camera.
-
-
-
There are six 3mm screws located on the interior frame.
-
Remove the screws with the screwdriver.
-
-
-
After the screws are removed gently pull the frame away from the rest of the camera.
-
The interior frame should now be disconnected.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935227:0crwdne2935227:0
crwdns2915084:0crwdne2915084:0
Clemson, Team 13-5, Benson Spring 2013 crwdns2935289:0Clemson, Team 13-5, Benson Spring 2013crwdne2935289:0
CLEM-BENSON-S13S13G5
crwdns2931471:03crwdne2931471:0
crwdns2935297:011crwdne2935297:0
