crwdns2915892:0crwdne2915892:0
This guide will show you how to replace your CASIO CDP-230R keys, move them to remove anything jamming your keys, or to move them to clean them.
crwdns2942213:0crwdne2942213:0
-
-
Flip the keyboard upside down, with the keys on a flat surface.
-
Remove the three black 14mm Japanese Industrial Standard (J) head screws using a J1 screwdriver on the top half of the outermost side panel.
-
-
-
Use two hands to grab the side panel from both sides.
-
Pull the panel apart from the device one side at a time.
-
-
-
Remove the three silver 10mm screws with a J1 screwdriver on the bottom half of the innermost side panel of the device.
-
-
-
Remove the innermost side panel by pinching the top and bottom of the panel and pulling the panel off with both hands.
-
-
-
Remove the two black 30 mm J head screws with a J1 screwdriver to remove the long black bar.
-
Remove the four silver 8mm x 2mm J head screws with a J1 screwdriver and the two brackets from the back panel.
-
-
-
-
Remove the eight silver 10mm x 1.5mm J head screws with a J1 screwdriver and the square tabs from the back panel.
-
Remove the eight silver 10mm J head screws with a J1 screwdriver underneath the square tabs.
-
-
-
Remove the 36 silver 10mm J head screws with a J1 screwdriver from the back panel.
-
-
-
Place a hand on the front panel and speakers and carefully flip the keyboard over with the keys facing up.
-
Grab the center of the front panel with two hands and lift to remove panel.
-
Grab the speakers from the sides and lift to remove. Once you have done this for the first speaker, repeat with the second speaker.
-
-
-
Locate the three screws behind the keys (left, center, and right).
-
Remove these 10mm J screws using a J1 screwdriver.
-
Grasp the white ribbon lined with foam and pull up to remove from the main circuit board.
-
-
-
Place one hand on the side with fingers underneath the keys and one hand on the upper edge and lift off of the back panel.
-
-
-
Pull up on the white key from the side nearest to you until the key lifts up.
-
-
-
Wiggle the white key from side to side and pull up to detach it from the rest of the board.
-
-
-
Flip the keyboard so the keys are laying on a flat surface.
-
Pull up on the black and white felt to dislodge the black shank.
-
Push up on the white key while pulling the felt up to reposition the black shank underneath the felt.
-
To reassemble your device, follow step 13 and then the rest of the instructions in reverse order.
To reassemble your device, follow step 13 and then the rest of the instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:013crwdne2935229:0
crwdns2915084:0crwdne2915084:0
Cal Poly, Team S4-G2, Livingston Fall 2017 crwdns2935289:0Cal Poly, Team S4-G2, Livingston Fall 2017crwdne2935289:0
CPSU-LIVINGSTON-F17S4G2
crwdns2931471:04crwdne2931471:0
crwdns2935297:06crwdne2935297:0
crwdns2947412:011crwdne2947412:0
Thankyou very much - I have a CDP-200R that I had to pull apart - yours was the only post I could find that helped me decode what it took!
Me too, I have 200R need to replace the keys, but afraid to dismantle , now you save us all.thank you
Searched everywhere on how to fix my Casio CDP-220RBK and this was all I could find that actually helped! Awesome and very helpful guide!!!
Thanks a lot. This manual is very detailed, and the only one I've found in the whole Internet.
Hello,
One of my kids lifted a black key from my piano. It won't come down fully and doesn't play when pressed. It's also harder to press, with more resistance.
Will I be able to put it back in place by following these instructions?
Many thanks.
