crwdns2933423:0crwdne2933423:0

Braun Series 7 790cc-7 Battery Replacement

crwdns2942213:0crwdne2942213:0

  1. Braun Series 7 790cc-7 Battery Replacement, Battery: crwdns2935265:01crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Braun Series 7 790cc-7 Battery Replacement, Battery: crwdns2935265:01crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • Use a spudger to remove the rubber piece on the back of the razor.

  2. Braun Series 7 790cc-7 Battery Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Use a Torx T8 to remove (4) 10 mm screws from housing.

  3. Braun Series 7 790cc-7 Battery Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Braun Series 7 790cc-7 Battery Replacement: crwdns2935265:03crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • Remove the rear cover from the device.

  4. Braun Series 7 790cc-7 Battery Replacement: crwdns2935265:04crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Remove the battery from the holster inside the device.

  5. Braun Series 7 790cc-7 Battery Replacement: crwdns2935265:05crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Replace the battery with a new 1300 mAh Sanyo (UR18500Y) battery.

    • Be sure to insert the battery the correct way.

crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2935229:027crwdne2935229:0

Alex Speer

crwdns2935283:011/07/17crwdne2935283:0

763 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2915084:0crwdne2915084:0

IUPUI, Team S3-G6, Harley Fall 2017 crwdns2935289:0IUPUI, Team S3-G6, Harley Fall 2017crwdne2935289:0

IUPUI-HARLEY-F17S3G6

crwdns2931471:03crwdne2931471:0

crwdns2935297:05crwdne2935297:0

crwdns2944067:027crwdne2944067:0

Any idea on how to remove/replace the drive unit? I bought a new one but the plastic backing is extremely hard to get off.

Chris - crwdns2934203:0crwdne2934203:0

Thank you for the awesome tutorial Alex!

I just wanted to comment that a small flat-head screw driver can be used to remove the 4 screws (under the rubber handle piece) if you don’t have a Torx tool. The screws each have 1 small slot across the head and if you’re careful you can remove and re-install them without too much trouble.

Thanks again for helping to save me a lot of trouble with this Alex… and avoid having to buy a new electric razor!

-jb-

arcticassault - crwdns2934203:0crwdne2934203:0

How do you reset the battery life indicator on the shaver after replacement?

jclemis - crwdns2934203:0crwdne2934203:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 20

crwdns2936753:07crwdne2936753:0 178

crwdns2936753:030crwdne2936753:0 837

crwdns2942667:0crwdne2942667:0 53,104