Bowers and Wilkins T7 Battery Replacement

crwdns2931653:01crwdne2931653:0 Access Panel

• As with all electronic devices, make sure your device is powered off before you begin.
• Gently lift up the access panel; it should easily "pop" open.
crwdns2913378:0crwdne2913378:0
crwdns2935261:0crwdne2935261:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:02crwdne2931653:0

• Remove 14mm screws on the front panel with a J1 Phillips head screwdriver.
• There are 8 screws in total.
crwdns2913378:0crwdne2913378:0
crwdns2935263:02crwdne2935263:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:03crwdne2931653:0
• Be gentle, the rubber seal is fragile and easy to tear, resulting in cosmetic damage to your device.
• Using the ifixit Opening Tool, carefully pry off the rubber seal around the sides.
• The seal is held by adhesive, if this is proving difficult you can use a heat gun to help the process.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:04crwdne2931653:0
• The cover is the most difficult part to remove. As you work, pry continuously, moving the tool around the device, working it a little further as you go.
• Using the ifixit Opening Tool, pry open at the seam found under the rubber seal.
• As the cover starts to come off, you can lift up using your hand.
crwdns2913378:0crwdne2913378:0
crwdns2935263:02crwdne2935263:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:05crwdne2931653:0
• Gently squeeze the internal locking mechanism inside the red and white terminals with either your fingers or a pair of precision tweezers.
• While squeezing the internal locking mechanism, pull back the terminal.
• Repeat this process for the second speaker.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:06crwdne2931653:0 Battery
• Using a cutting tool such as a Jimmy steel blade or wire cutter, cut the cable tie surrounding the battery.
• Be careful not to damage the battery while cutting the cable tie surrounding the battery.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:07crwdne2931653:0
• Using the ifixit Opening Tool, pry out the battery power supply connector.
• Pull and remove the battery power supply connector.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:08crwdne2931653:0
• After disconnecting the power supply connector, pull the battery out of its case.
crwdns2913378:0crwdne2913378:0
crwdns2935261:0crwdne2935261:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:02crwdnd2935293:0crwdne2935293:0

Bertrand Plummer

crwdns2935283:002/28/17crwdne2935283:0

251 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2918514:0crwdne2918514:0: 6

• 
• 
• 

crwdns2935301:03crwdne2935301:0

crwdns2915084:0crwdne2915084:0

USF Tampa, Team S7-G1, Cagle Spring 2017 crwdns2935289:0USF Tampa, Team S7-G1, Cagle Spring 2017crwdne2935289:0

USFT-CAGLE-S17S7G1

crwdns2931471:05crwdne2931471:0

crwdns2935297:04crwdne2935297:0

crwdns2942557:0crwdne2942557:0

crwdns2942955:0crwdne2942955:0

crwdns2852917:0crwdne2852917:0