Apple Time Capsule Model A1254 Fan Replacement

crwdns2931653:01crwdne2931653:0 Back Plate




• Turn the device upside down to reveal the rubber section of the back plate. Using a metal spudger, carefully wedge the blunt tip into the space between the aluminum back plate and the rubber, separating the two pieces.
• This may take a few minutes to pry the rubber off completely. Once your are able to get a grip on the rubber it is easier to peel it off using your hands.
• Depending on air temperature and how set the adhesive is, you may need to spend some time warming the back plate with a hot plate (on low) or hair dryer.
• Don't worry about re-applying adhesive to the rubber; the remaining adhesive has plenty of strength to affix itself to the aluminum.
crwdns2913378:0crwdne2913378:0
crwdns2935263:09crwdne2935263:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:02crwdne2931653:0



• Remove the ten 3mm screws with a Phillips #00 screwdriver.
• The screws with adhesive covering do not need to be removed.
crwdns2913378:0crwdne2913378:0
crwdns2935263:04crwdne2935263:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:03crwdne2931653:0
• The fan affixed to the back plate is connected to the logic board. A small wire must be detached to fully remove the back plate.
• Pull the base of the wire close to the logic board and the connector will pop off.
crwdns2913378:0crwdne2913378:0
crwdns2935263:02crwdne2935263:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:04crwdne2931653:0 Fan
• Orientate the back plate so that the fan is facing away from you.
• Use the #0 Phillips Screw Drive to push the rubber shock mounts through the back plate.
• Make sure that the head of the screw driver is centered on the head of the rubber shock mount so that it doesn't slip off causing possible injury.
• When attaching the new fan, push the new rubber shock mounts through the back plate first. Attach the fan once all mounts are inserted.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0

crwdns2862417:0crwdne2862417:0

crwdns2935291:0crwdnd2935291:01crwdnd2935291:0crwdne2935291:0

JR Alfano

crwdns2935283:010/06/16crwdne2935283:0

528 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2918514:0crwdne2918514:0: 7

• 
• 
• 

crwdns2935301:04crwdne2935301:0

crwdns2915084:0crwdne2915084:0

Cal Poly, Team 4-2, Livingston Fall 2016 crwdns2935289:0Cal Poly, Team 4-2, Livingston Fall 2016crwdne2935289:0

CPSU-LIVINGSTON-F16S4G2

crwdns2931471:04crwdne2931471:0

crwdns2935297:017crwdne2935297:0

crwdns2942557:0crwdne2942557:0

crwdns2942955:0crwdne2942955:0

crwdns2852917:0crwdne2852917:0