crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Apple TV 1st Generation Lower Case Replacement

crwdns2915892:0crwdne2915892:0

Remove the lower case in your Apple TV 1st Generation.

crwdns2942213:0crwdne2942213:0

  1. Apple TV 1st Generation Lower Case Replacement, Lower Case: crwdns2935265:01crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Flip the Apple TV over so that the bottom of the unit is facing up.

    • You need to remove the rubber base to get access to the screws.

    • Starting at one side of the device, use a hairdryer or a heat gun to soften the adhesive holding the rubber base in place.

    • The rubber base will be hot after heating, take extreme caution while proceeding to avoid personal injury.

    • While the adhesive is still warm, peel the bottom of the rubber base upwards to detach it from the metal plate.

    • The rubber base can tear if the adhesive hasn't been softened enough.

    • Repeat the procedure described above until the rubber base has been completely removed.

    crwdns2913378:0crwdne2913378:0

  2. Apple TV 1st Generation Lower Case Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Remove the four T10 Torx screws that secure the lower case to the upper case.

    crwdns2913378:0crwdne2913378:0

  4. Apple TV 1st Generation Lower Case Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Carefully lift the lower case from the upper case enough to allow access to the internals of the Apple TV.

    • Be aware that the hard drive is physically attached to the lower case and that a ribbon cable runs from the drive to the logic board in the upper case.

    crwdns2913378:0crwdne2913378:0

  5. Apple TV 1st Generation Lower Case Replacement: crwdns2935265:04crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Apple TV 1st Generation Lower Case Replacement: crwdns2935265:04crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Carefully pull the hard drive data cable straight up from its socket on the logic board.

    • During reassembly, make sure the hard drive data cable is firmly seated in its socket on the logic board; otherwise, during boot-up you will see a flashing question mark "?".

    crwdns2913378:0crwdne2913378:0
crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2935229:03crwdne2935229:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:020crwdnd2935293:0crwdne2935293:0

CCarvalho

crwdns2935283:011/08/09crwdne2935283:0

283 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2918514:0crwdne2918514:0: 11

crwdns2935301:08crwdne2935301:0

crwdns2915084:0crwdne2915084:0

Cal Poly, Team 18-5, Maness Fall 2009 crwdns2935289:0Cal Poly, Team 18-5, Maness Fall 2009crwdne2935289:0

CPSU-MANESS-F09S18G5

crwdns2931471:05crwdne2931471:0

crwdns2935297:07crwdne2935297:0

crwdns2947410:01crwdne2947410:0

This guide may make more sense as a teardown, since its not really showing any repairs or replacements.

Alex Jansen - crwdns2934203:0crwdne2934203:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 0

crwdns2936753:07crwdne2936753:0 2

crwdns2936753:030crwdne2936753:0 18

crwdns2942667:0crwdne2942667:0 8,597