crwdns2915892:0crwdne2915892:0
Sometimes screens stop working. This guide will show you how to replace your screen and get back to browsing.
crwdns2942213:0crwdne2942213:0
-
-
Slide the tab over to unlock the battery cover located on the bottom-left corner of the laptop.
-
-
-
Lift the exposed lip and remove the battery cover.
-
-
-
Press the tabs on the battery and lift them. The battery should come out easily.
-
-
-
Using the PH1 screwdriver, remove the four 4 .75 mm screws that are located on the vent panel.
-
-
-
Remove the one .5 mm screw located in the top right corner of the battery compartment.
-
-
-
Remove the bottom panel by sliding it toward the hinges and lifting the back panel up.
-
-
-
Unplug the wire cable attached to the fan by pulling it out .
-
-
-
Using the PH1 screwdriver, remove the 3 .75mm screws labeled as 1, 2, and 3 on the fan. NOTE these screws have the labels "1", "2", and "3" next to them.
-
Lift the fan up with your fingers.
-
-
-
Using the PH1 screwdriver remove the two .75 mm screws from the hinge side of the laptop.
-
-
-
Using the PH1 screwdriver, remove the four .75 mm screws from the copper heat sync. They will be labeled 1-4.
-
Pull the copper heat sync out of the laptop.
-
-
-
Using the PH1 screwdriver, remove four .75 mm screws from the driver, located in the bottom-right corner of the laptop.
-
-
-
Pull on the black tab on the driver to slide the driver back, and lift the driver out of the laptop.
-
-
-
Using the PH1 screwdriver, remove the five .5 mm screws from the SD card reader, located in the bottom-middle corner of the laptop.
-
Slide the SD card reader away and out.
-
-
-
Detach the white and black wires from the Wi-Fi card, located in the central area of the laptop.
-
-
-
Using the PH 1 screwdriver, remove the two .25 mm screws from the Wi-Fi card.
-
-
-
-
Slide the Wi-Fi card out of its slot to remove.
-
-
-
Using the PH1mm screwdriver, remove one .5 mm screw from the disk drive, located inthe top-right corner of the laptop.
-
-
-
Slide the disc drive out of its slot.
-
-
-
Using the PH 1 screwdriver, remove the two .5 mm screws from the RAM drive.
-
-
-
Slide and lift the RAMdrive out of its port.
-
-
-
Using the PH1 screwdriver, remove the .75 mm screw from the plastic housing corner, located in the bottom-right corner of the laptop.
-
-
-
Unplug the black cable from the central area of the laptop.
-
-
-
Unplug the wire cable in the central area of the laptop.
-
-
-
Unplug the wire and black cables on the motherboard, located in the upper-left corner of the laptop.
-
-
-
Using the PH1 screwdriver, unscrew the two .75 mm screws from the top-left corner of the motherboard.
-
-
-
Using the PH 1 screwdriver, remove the .75 cm screw from the top-middle section of the motherboard.
-
-
-
Using the PH1 screwdriver, remove the .75 mm screw from the top-middle corner of the motherboard.
-
-
-
Using the PH1 screwdriver, remove the three .75 mm screws from the bottom corner of the motherboard.
-
-
-
Slide the motherboard to the right and lift it up, but do not pull it completely out.
-
-
-
Gently unplug the ribbon cable from the underside of the motherboard.
-
-
-
Use the metal spudger or opening tool across the top edge of the keyboard to pop it out.
-
-
-
Use the metal spudger or opening tool to pop out the plastic hinge covers.
-
-
-
Use the PH1 screwdriver to remove the .75 mm screws from the hinges. Each hinge has one screw.
-
-
-
The screen should separate from the rest of the laptop.
-
-
-
Using the PH1 screwdriver, remove the .75 mm screw from the bottom-middle section was previously covering.
-
-
-
Using the PH 1 screwdriver, remove the .75 cm screw from the bottom-middle section where the keyboard was previously covering.
-
-
-
Lift the front cover off of the laptop.
-
-
-
Flip the laptop back over. The charging port will be located in the top-right corner.
-
-
-
Using a metal spudger, pop off the six rubber screw covers.
-
-
-
Using the PH1mm screwdriver, remove the six .75 mm screws from the front of the screen frame.
-
-
-
Use the plastic opening tool or spudger along the edge of the frame, to pry off the frame.
-
-
-
Using the PH1 screwdriver, remove the four bottom .75 mm screws from the screen frame.
-
-
-
Using the PH1 screwdriver, remove the two .75 cm screws from the top of the screen frame.
-
-
-
Lift the bracket off the top of the screen frame.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935227:0crwdne2935227:0
crwdns2915084:0crwdne2915084:0
Eastern Washington University, Team S1-G3, Carnegie Fall 2017 crwdns2935289:0Eastern Washington University, Team S1-G3, Carnegie Fall 2017crwdne2935289:0
EWU-CARNEGIE-F17S1G3
crwdns2931471:04crwdne2931471:0
crwdns2935297:05crwdne2935297:0
crwdns2947412:03crwdne2947412:0
Very well done. Thank You
Thank you for your time!
Now, I don´t know how to connect the cables to the motherboard because they are too short.
