crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

Repair information and guides for the iPhone 6 that was released on September 19, 2014. Model Numbers: A1549, A1586, and A1589

crwdns2934591:04994crwdne2934591:0 crwdns2934593:0crwdne2934593:0

crwdns2933897:0crwdne2933897:0

Touch is not working. Missing a voltage?

Hello all,

More of a technical question... I have an iPhone 6 with no touch. Before lifting cumulus I was poking around for voltages and am missing PP5V1_GRAPE_VDDH. There is no short to ground on that line.

I pulled U1501 and replaced it with one I had on a doaner board that might have been bad. I lost all image on the screen but had backlight after that.

Retracing my steps, I reballed the original U1501 an stuck it back on and the phone is back to how it was.

Should I order and install a new U1501 or is there something else you would advise me to check first?

Thanks all and happy repairing!

Joseph

crwdns2934081:0crwdne2934081:0 crwdns2934083:0crwdne2934083:0 crwdns2934093:0crwdne2934093:0

crwdns2934109:0crwdne2934109:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 0
crwdns2934285:0crwdne2934285:0

crwdns2933313:01crwdne2933313:0

crwdns2934221:0crwdne2934221:0
crwdns2931211:0crwdne2931211:0 crwdns2931215:0crwdne2931215:0 crwdns2934225:0crwdne2934225:0
crwdns2934051:0crwdne2934051:0

crwdns2933897:0crwdne2933897:0

did you try meson to see if it could be an issue

crwdns2934105:0crwdne2934105:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 2

crwdns2944067:028crwdne2944067:0:

Honestly no I have not. Before pulling it off I thought I would check voltages going to the two.

If it were an ip6+ they for sure first thing would be an M1 jumper. But in this case, no stress on the board seems to make any difference in it working, so I was leaning away from classic touch diseases (also being a 6 not a 6 plus) are there some inputs I should test out for menson? Or what would you recommend I do to it?

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

cumulus and meson have connected lines like CUMULUS_TO_MESON_VSTM_OUT_N, CUMULUS_TO_MESON_VSTM_OUT_P, CUMULUS_TO_SAGE_BOOST_CLK_EN, TOUCH_I2C_SCL, TOUCH_I2C_SDA

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

also did you check resistance on j2401

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

I didn't check resistances on j2401, somehow that passed my mind .... Surprised. That could easily tell me what it might be.

Is it normal for U1501 to have 2 of the 3 power outputs OK and the third dead? That's my primary thought on this one at the moment. I don't have the schematics here with me at home, butbinkimda thought that they would all be present, or none.

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

I will definitely check those lines though on Monday

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

crwdns2934275:023crwdne2934275:0

crwdns2934285:0crwdne2934285:0

crwdns2934229:0crwdne2934229:0

Joseph Hughes crwdns2934231:0crwdne2934231:0
crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 0

crwdns2936753:07crwdne2936753:0 0

crwdns2936753:030crwdne2936753:0 0

crwdns2942667:0crwdne2942667:0 564