crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

Repair information and guides for the iPhone 6S released by Apple on September 25, 2015. Models: A1688, A1633

crwdns2934591:02687crwdne2934591:0 crwdns2934593:0crwdne2934593:0

crwdns2933897:0crwdne2933897:0

Not charging after screen replacement

So i replaced the screen on an iphone 6s, the phone was brought to me almost dead just flashing battery, put it on charger and it charged to 35 percent. So i proceeded with the repair, so its safe to say the battery would charge before i replaced the screen. Installed new screen, turns on everything fine. But when plugged into charger it shows charging but its not charging the battery. I have ordered a new battery for it to see if that will fix the issue. I have tried a reset by holding down the home button and power button. I know i fully discharged the power aswell before removing the screen. I always hold down the power button before removing screens. Any idea how or what could cause this?

crwdns2934081:0crwdne2934081:0 crwdns2934083:0crwdne2934083:0 crwdns2934093:0crwdne2934093:0

crwdns2934109:0crwdne2934109:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 0
crwdns2934285:0crwdne2934285:0

crwdns2933315:02crwdne2933315:0

crwdns2934221:0crwdne2934221:0
crwdns2931211:0crwdne2931211:0 crwdns2931215:0crwdne2931215:0 crwdns2934225:0crwdne2934225:0
crwdns2934051:0crwdne2934051:0

crwdns2933897:0crwdne2933897:0

Holding power button is pointless, disconnecting battery and waiting about 5 - 10 seconds is enough to discharge everything.

As for your issue, there could be a few possibilities, you may have knocked something off during repair, or accidentally hit something and damaged it.

You could also have a poor quality screen that drains more power than an original screen.

The problem could of also been there beforehand, it could be a tristar chip issue from cheap cable damage, as tristar can cause the phone to only charge up to a certain percentage and it can also cause the fake charging issue that you're experiencing. :-)

crwdns2934105:0crwdne2934105:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 1

crwdns2944067:02crwdne2944067:0:

after the replacement of the screen, the battery was really low, put on charger and it went to 8 percent. I guess it never went past that. I am guess you have experienced this yourself before. Got the screen from Injured gadgets was 75 for it. I know nothing about micro soldering nor the setup for it. Something that i would like to get into very soon.

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

Yes these are some of the symptoms of tristar chip damage, this would require micro soldering.

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

crwdns2934285:0crwdne2934285:0
crwdns2934057:0crwdne2934057:0

crwdns2933897:0crwdne2933897:0

No need to hold power button after unplugging battery.

You only need to wait 5 seconds after unplugging battery.

Have you tried a another charging port flex cable?

crwdns2934105:0crwdne2934105:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 2
crwdns2934285:0crwdne2934285:0

crwdns2934229:0crwdne2934229:0

mikebarkas crwdns2934231:0crwdne2934231:0
crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 3

crwdns2936753:07crwdne2936753:0 10

crwdns2936753:030crwdne2936753:0 49

crwdns2942667:0crwdne2942667:0 10,574