crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

Apple's 2012 first-generation 7.9-inch iPad mini, with 16, 32, or 64 GB of storage and an A5 processor.

crwdns2934591:0630crwdne2934591:0 crwdns2934593:0crwdne2934593:0
crwdns2934055:0crwdne2934055:0

crwdns2933897:0crwdne2933897:0

potential problems by soldering the ic chip incorrectly?

Hi

is there any potential pronlems if I solder my own ic chip to a new digitiser? Would it blow anything if a couple of contacts were touching? Or would it simply not work?

Would like to practice this, but not at the expense of someones ipad when i repair it.

would be handy to do, as im fed up of these cheap ones which flicker everytime I lay it flat, and have to cover it in tape.

Thanks

crwdns2934089:0crwdne2934089:0 crwdns2934093:0crwdne2934093:0

crwdns2934109:0crwdne2934109:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 0
crwdns2934285:0crwdne2934285:0

crwdns2933313:01crwdne2933313:0

crwdns2934221:0crwdne2934221:0
crwdns2931211:0crwdne2931211:0 crwdns2931215:0crwdne2931215:0 crwdns2934225:0crwdne2934225:0
crwdns2934057:0crwdne2934057:0

crwdns2933897:0crwdne2933897:0

Most likely worst case scenario: dead device.

Update

If you don't do it right, you could get the power leads or voltage to where they don't belong. Hence possibility of a dead device is strong.

crwdns2934105:0crwdne2934105:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 2

crwdns2944067:03crwdne2944067:0:

Is that fact or just a guess? Just that I would think as the connections would only ne sending signals, then I would imagine the digitiser would go a bit loopy as if the flex cable was pinched? But that's just a guess. Wonder if anyone has actually done it wrong? I know all the local repair shops in this area don't solder the parts.

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

If you don't do it right, you could get the power leads or voltage to where they don't belong. Hence possibility of a dead device is strong.

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

Ok, I'm not really experienced at soldering, but practice makes perfect.

wonder if there's some sort of schematic for that connection?

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

crwdns2934285:0crwdne2934285:0
crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 0

crwdns2936753:07crwdne2936753:0 0

crwdns2936753:030crwdne2936753:0 0

crwdns2942667:0crwdne2942667:0 106