crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0
crwdns2918538:0crwdne2918538:0

crwdns2934243:0crwdne2934243:0 Zack Sg

crwdns2947189:0crwdne2947189:0:

Can MG 8331S be soldered on?

crwdns2934249:0crwdne2934249:0:

I am planning to purchase the MG 8331S to repair my burnt battery connector area. Currently, the vias are exposed and I'm planning to use normal epoxy to patch the areas around the vias before using the silver conductive epoxy.
[image|2746283]
However, I'm not sure if the MG 8331S can be soldered on after curing. A previous answer says it can be ([post|61241]) while other forums and some 8331 products' datasheets it can't.
Thank you in advance.
Edit1: General area.
[image|2747051]
Edit2: Battery Clip Connector Component (board side - female)
[image|2747060]
Location on board:
[image|2747058]
[image|2747061]
Edit3:
[image|2747065]
-[image|2747066] (Flipped over the connector)
+[image|2747066]
+
+(Flipped over the connector)

crwdns2866306:0crwdne2866306:0:

Soldering

crwdns2915684:0crwdne2915684:0:

open

crwdns2934251:0crwdne2934251:0:

+750010

crwdns2934245:0crwdne2934245:0 Zack Sg

crwdns2947189:0crwdne2947189:0:

Can MG 8331S be soldered on?

crwdns2934249:0crwdne2934249:0:

I am planning to purchase the MG 8331S to repair my burnt battery connector area. Currently, the vias are exposed and I'm planning to use normal epoxy to patch the areas around the vias before using the silver conductive epoxy.
[image|2746283]
However, I'm not sure if the MG 8331S can be soldered on after curing. A previous answer says it can be ([post|61241]) while other forums and some 8331 products' datasheets it can't.
Thank you in advance.
Edit1: General area.
[image|2747051]
Edit2: Battery Clip Connector Component (board side - female)
[image|2747060]
Location on board:
-[image|2747058] (Source: https://www.ifixit.com/Guide/Samsung+Galaxy+Note20+Ultra+Motherboard+Replacement/142701)
+[image|2747058]
[image|2747061]
+
+Edit3:
+
+[image|2747065]
+
+[image|2747066] (Flipped over the connector)

crwdns2866306:0crwdne2866306:0:

Soldering

crwdns2915684:0crwdne2915684:0:

open

crwdns2934245:0crwdne2934245:0 Zack Sg

crwdns2947189:0crwdne2947189:0:

Can MG 8331S be soldered on?

crwdns2934249:0crwdne2934249:0:

I am planning to purchase the MG 8331S to repair my burnt battery connector area. Currently, the vias are exposed and I'm planning to use normal epoxy to patch the areas around the vias before using the silver conductive epoxy.
[image|2746283]
However, I'm not sure if the MG 8331S can be soldered on after curing. A previous answer says it can be ([post|61241]) while other forums and some 8331 products' datasheets it can't.
Thank you in advance.
-Edit1: General area. [image|2747051]
+Edit1: General area.
+
+[image|2747051]
+
+Edit2: Battery Clip Connector Component (board side - female)
+
+[image|2747060]
+
+Location on board:
+
+[image|2747058] (Source: https://www.ifixit.com/Guide/Samsung+Galaxy+Note20+Ultra+Motherboard+Replacement/142701)
+
+[image|2747061]

crwdns2866306:0crwdne2866306:0:

Soldering

crwdns2915684:0crwdne2915684:0:

open

crwdns2934245:0crwdne2934245:0 Zack Sg

crwdns2947189:0crwdne2947189:0:

Can MG 8331S be soldered on?

crwdns2934249:0crwdne2934249:0:

I am planning to purchase the MG 8331S to repair my burnt battery connector area. Currently, the vias are exposed and I'm planning to use normal epoxy to patch the areas around the vias before using the silver conductive epoxy.
[image|2746283]
However, I'm not sure if the MG 8331S can be soldered on after curing. A previous answer says it can be ([post|61241]) while other forums and some 8331 products' datasheets it can't.
Thank you in advance.
+
+Edit1: General area. [image|2747051]

crwdns2866306:0crwdne2866306:0:

Soldering

crwdns2915684:0crwdne2915684:0:

open

crwdns2934241:0crwdne2934241:0 Zack Sg

crwdns2947189:0crwdne2947189:0:

Can MG 8331S be soldered on?

crwdns2934249:0crwdne2934249:0:

I am planning to purchase the MG 8331S to repair my burnt battery connector area. Currently, the vias are exposed and I'm planning to use normal epoxy to patch the areas around the vias before using the silver conductive epoxy.

[image|2746283]

However, I'm not sure if the MG 8331S can be soldered on after curing. A previous answer says it can be ([post|61241]) while other forums and some 8331 products' datasheets it can't.

Thank you in advance.

crwdns2866306:0crwdne2866306:0:

Soldering

crwdns2915684:0crwdne2915684:0:

open