Water and electronics and electricity are not a good mix.
''The impurities in the water causes corrosion and provides circuit paths for the electricity which were not in the phone's operating design and could damage the components. The corrosion is ongoing until it has been properly cleaned away.''
First '''do not try to charge or to turn on your phone''' and then you need to '''remove the battery''' as soon as possible to prevent any further damage.
-
Then you need to dis-assemble the rest of the phone and clean ''all the affected parts'' using '''Isopropyl Alcohol 99%+''' (available from electronics parts stores) to remove all traces of corrosion and water. Try not to use "rubbing alcohol" as in some cases this is <70% IPA, can contain additives and is not as effective. If you do have to use it, check the label to verify the amount of IPA.
+
Then you need to dis-assemble the rest of the phone and clean ''all the affected parts'' using '''Isopropyl Alcohol 99%+''' (available from electronics parts stores) to remove all traces of corrosion and water. Try not to use "rubbing alcohol" as in some cases this is <70% IPA, can contain additives and is not as effective. If you do have to use it, check the label to verify the amount of IPA. The higher the percentage of IPA, the better.
Here is a link that describes the process. [[Electronics Water Damage]]
As always with electronics, especially surface mounted PCBs be gentle when handling and especially when brushing away the corrosion. You do not want to remove any components from the boards. You will also have to remove any shields that are covering some components and disconnect and clean any cable connectors etc
Hopefully after you have done all this the phone ''might'' possibly work correctly again.
Here is a link to the ifixit [[Topic:Moto G6 Plus]] guides which may be of some help.
If this process seems too daunting, take your phone to a reputable, professional mobile phone repair service, ''experienced in water damage repair'' and ask for a quote for a repair.
If you decide to do this, ''do it sooner than later''.
Water and electronics and electricity are not a good mix.
''The impurities in the water causes corrosion and provides circuit paths for the electricity which were not in the phone's operating design and could damage the components. The corrosion is ongoing until it has been properly cleaned away.''
First '''do not try to charge or to turn on your phone''' and then you need to '''remove the battery''' as soon as possible to prevent any further damage.
-
Then you need to dis-assemble the rest of the phone and clean ''all the affected parts'' using '''Isopropyl Alcohol 99%+''' (available from electronics parts stores) to remove all traces of corrosion and water. Do not use "rubbing alcohol" as in some cases this is <70% IPA, can contain additives and is not as effective. If you do have to use it, check the label to verify the amount of IPA.
+
Then you need to dis-assemble the rest of the phone and clean ''all the affected parts'' using '''Isopropyl Alcohol 99%+''' (available from electronics parts stores) to remove all traces of corrosion and water. Try not to use "rubbing alcohol" as in some cases this is <70% IPA, can contain additives and is not as effective. If you do have to use it, check the label to verify the amount of IPA.
Here is a link that describes the process. [[Electronics Water Damage]]
As always with electronics, especially surface mounted PCBs be gentle when handling and especially when brushing away the corrosion. You do not want to remove any components from the boards. You will also have to remove any shields that are covering some components and disconnect and clean any cable connectors etc
Hopefully after you have done all this the phone ''might'' possibly work correctly again.
Here is a link to the ifixit [[Topic:Moto G6 Plus]] guides which may be of some help.
If this process seems too daunting, take your phone to a reputable, professional mobile phone repair service, ''experienced in water damage repair'' and ask for a quote for a repair.
If you decide to do this, ''do it sooner than later''.
Water and electronics and electricity are not a good mix.
''The impurities in the water causes corrosion and provides circuit paths for the electricity which were not in the phone's operating design and could damage the components. The corrosion is ongoing until it has been properly cleaned away.''
First '''do not try to charge or to turn on your phone''' and then you need to '''remove the battery''' as soon as possible to prevent any further damage.
Then you need to dis-assemble the rest of the phone and clean ''all the affected parts'' using '''Isopropyl Alcohol 99%+''' (available from electronics parts stores) to remove all traces of corrosion and water. Do not use "rubbing alcohol" as in some cases this is <70% IPA, can contain additives and is not as effective. If you do have to use it, check the label to verify the amount of IPA.
Here is a link that describes the process. [[Electronics Water Damage]]
As always with electronics, especially surface mounted PCBs be gentle when handling and especially when brushing away the corrosion. You do not want to remove any components from the boards. You will also have to remove any shields that are covering some components and disconnect and clean any cable connectors etc
Hopefully after you have done all this the phone ''might'' possibly work correctly again.
Here is a link to the ifixit [[Topic:Moto G6 Plus]] guides which may be of some help.
If this process seems too daunting, take your phone to a reputable, professional mobile phone repair service, ''experienced in water damage repair'' and ask for a quote for a repair.
If you decide to do this, ''do it sooner than later''.