Your best bet is to open the tablet, disconnect the battery, (do not short circuit the battery leads when you remove them from the board, individually insulate them to prevent this from happening) and remove the systemboard from the case.
Then you need to '''gently''' wipe clean both sides of the systemboard completely using isopropyl alcohol 90%+ and a Qtip to remove any trace of water and the corrosion that may be caused by the contaminants in the water.
''Notice how I am stressing ''''gently''''. You do not wish to brush the components off the systemboard.''
You will also have to clean the battery pcb and all the other components in the case in the same way.
-
When you are satisfied that you have got it all clean, allow it to dry for at least 24hours before replacing all the components (systemboard/battery/ speakers/ buttons etc) and reconnecting the battery and hope that, because you have been careful and thorough that it will turn on and perform normally
+
When you are satisfied that you have got it all clean, allow it to dry for at least 24hours before replacing all the components (systemboard/battery/ speakers/ buttons etc) and reconnecting the battery and hope that, because you have been careful and thorough that it will turn on and perform normally. Test it works before replacing the cover.
Your best bet is to open the tablet, disconnect the battery, (do not to short circuit the battery leads when you remove them from the board, individually insulate them to prevent this from happening) and remove the systemboard from the case.
+
Your best bet is to open the tablet, disconnect the battery, (do not short circuit the battery leads when you remove them from the board, individually insulate them to prevent this from happening) and remove the systemboard from the case.
Then you need to '''gently''' wipe clean both sides of the systemboard completely using isopropyl alcohol 90%+ and a Qtip to remove any trace of water and the corrosion that may be caused by the contaminants in the water.
''Notice how I am stressing ''''gently''''. You do not wish to brush the components off the systemboard.''
You will also have to clean the battery pcb and all the other components in the case in the same way.
When you are satisfied that you have got it all clean, allow it to dry for at least 24hours before replacing all the components (systemboard/battery/ speakers/ buttons etc) and reconnecting the battery and hope that, because you have been careful and thorough that it will turn on and perform normally
Your best bet is to open the tablet, disconnect the battery, (do not to short circuit the battery leads when you remove them from the board, individually insulate them to prevent this from happening) and remove the systemboard from the case.
Then you need to '''gently''' wipe clean both sides of the systemboard completely using isopropyl alcohol 90%+ and a Qtip to remove any trace of water and the corrosion that may be caused by the contaminants in the water.
''Notice how I am stressing ''''gently''''. You do not wish to brush the components off the systemboard.''
-
You will also have to clean the battery terminals and the pcb connected to the battery and all the other components in the case in the same way.
+
You will also have to clean the battery pcb and all the other components in the case in the same way.
When you are satisfied that you have got it all clean, allow it to dry for at least 24hours before replacing all the components (systemboard/battery/ speakers/ buttons etc) and reconnecting the battery and hope that, because you have been careful and thorough that it will turn on and perform normally
Your best bet is to open the tablet, disconnect the battery, (do not to short circuit the battery leads when you remove them from the board, individually insulate them to prevent this from happening) and remove the systemboard from the case.
-
Then you need to '''gently''' wipe clean both sides of the systemboard using isopropyl alcohol 90%+ and a Qtip to remove any trace of water and the corrosion that may be caused by the contaminants in the water.
+
Then you need to '''gently''' wipe clean both sides of the systemboard completely using isopropyl alcohol 90%+ and a Qtip to remove any trace of water and the corrosion that may be caused by the contaminants in the water.
''Notice how I am stressing ''''gently''''. You do not wish to brush the components off the systemboard.''
You will also have to clean the battery terminals and the pcb connected to the battery and all the other components in the case in the same way.
When you are satisfied that you have got it all clean, allow it to dry for at least 24hours before replacing all the components (systemboard/battery/ speakers/ buttons etc) and reconnecting the battery and hope that, because you have been careful and thorough that it will turn on and perform normally
Your best bet is to open the tablet, disconnect the battery, (do not to short circuit the battery leads when you remove them from the board, individually insulate them to prevent this from happening) and remove the systemboard from the case.
-
Then you need to '''gently''' wipe clean both sides of the systemboard using isopropyl alcohol 90%+and a Qtip to remove any trace of water and the corrosion that may be caused by the contaminants in the water.
+
Then you need to '''gently''' wipe clean both sides of the systemboard using isopropyl alcohol 90%+ and a Qtip to remove any trace of water and the corrosion that may be caused by the contaminants in the water.
''Notice how I am stressing ''''gently''''. You do not wish to brush the components off the systemboard.''
You will also have to clean the battery terminals and the pcb connected to the battery and all the other components in the case in the same way.
When you are satisfied that you have got it all clean, allow it to dry for at least 24hours before replacing all the components (systemboard/battery/ speakers/ buttons etc) and reconnecting the battery and hope that, because you have been careful and thorough that it will turn on and perform normally
Your best bet is to open the tablet, disconnect the battery, (do not to short circuit the battery leads when you remove them from the board, insulate them to prevent this from happening) and remove the systemboard from the case.
+
Your best bet is to open the tablet, disconnect the battery, (do not to short circuit the battery leads when you remove them from the board, individually insulate them to prevent this from happening) and remove the systemboard from the case.
Then you need to '''gently''' wipe clean both sides of the systemboard using isopropyl alcohol 90%+and a Qtip to remove any trace of water and the corrosion that may be caused by the contaminants in the water.
''Notice how I am stressing ''''gently''''. You do not wish to brush the components off the systemboard.''
You will also have to clean the battery terminals and the pcb connected to the battery and all the other components in the case in the same way.
When you are satisfied that you have got it all clean, allow it to dry for at least 24hours before replacing all the components (systemboard/battery/ speakers/ buttons etc) and reconnecting the battery and hope that, because you have been careful and thorough that it will turn on and perform normally
Hi,
Your best bet is to open the tablet, disconnect the battery, (do not to short circuit the battery leads when you remove them from the board, insulate them to prevent this from happening) and remove the systemboard from the case.
Then you need to '''gently''' wipe clean both sides of the systemboard using isopropyl alcohol 90%+and a Qtip to remove any trace of water and the corrosion that may be caused by the contaminants in the water.
''Notice how I am stressing ''''gently''''. You do not wish to brush the components off the systemboard.''
You will also have to clean the battery terminals and the pcb connected to the battery and all the other components in the case in the same way.
When you are satisfied that you have got it all clean, allow it to dry for at least 24hours before replacing all the components (systemboard/battery/ speakers/ buttons etc) and reconnecting the battery and hope that, because you have been careful and thorough that it will turn on and perform normally