Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp. I assume it has the Bose system. Should be inside the center console, just pull the cup holders up to see if it is there.
+
Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp. I assume it has the Bose system. Should be inside the center console, just pull the cup holders up to see if it is there.
+
AMPLIFIER REPLACEMENT
+
REMOVAL PROCEDURE
-
1. If equipped with a Bose(TM) amplifier, remove the radio amp fuse located
-
under the hood electrical center.
+
+
1. If equipped with a Bose(TM) amplifier, remove the radio amp fuse located under the hood electrical center.
+
2. Remove the floor console bezel.
+
3. Remove the cupholder.
+
4. Remove the bolts (1) retaining the console to the instrument panel (I/P).
+
5. Remove the console storage bin.
+
6. Remove the center console end panel.
+
7. Disconnect the audio amplifier electrical connectors.
-
8. Remove the 4 screws retaining the upper console bracket to the lower
-
console bracket.
+
+
8. Remove the 4 screws retaining the upper console bracket to the lower console bracket.
+
9. Move both front seats to the fully forward.
+
10. Reposition the inboard seat track trim (1) in order to gain access to the rear console side panel screw (2).
+
11. Remove both rear console side panel screws
+
12. Move both front seats to the fully rearward.
+
13. Remove both front console side panel screws (1).
+
14. Disconnect the floor console electrical connector.
+
15. Remove the console assembly from the vehicle.
+
16. Remove the audio amplifier screws (1).
-
17. Remove the audio amplifier from the vehicle. Hope this helps, good luck.
Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp. I assume it has the Bose system. Check under the rear seat on the drivers side. there should be a black box and you will need to remove the cover. Hope this helps, good luck.
+
Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp. I assume it has the Bose system. Should be inside the center console, just pull the cup holders up to see if it is there.
+
AMPLIFIER REPLACEMENT
+
REMOVAL PROCEDURE
+
1. If equipped with a Bose(TM) amplifier, remove the radio amp fuse located
+
under the hood electrical center.
+
2. Remove the floor console bezel.
+
3. Remove the cupholder.
+
4. Remove the bolts (1) retaining the console to the instrument panel (I/P).
+
5. Remove the console storage bin.
+
6. Remove the center console end panel.
+
7. Disconnect the audio amplifier electrical connectors.
+
8. Remove the 4 screws retaining the upper console bracket to the lower
+
console bracket.
+
9. Move both front seats to the fully forward.
+
10. Reposition the inboard seat track trim (1) in order to gain access to the rear console side panel screw (2).
+
11. Remove both rear console side panel screws
+
12. Move both front seats to the fully rearward.
+
13. Remove both front console side panel screws (1).
+
14. Disconnect the floor console electrical connector.
+
15. Remove the console assembly from the vehicle.
+
16. Remove the audio amplifier screws (1).
+
17. Remove the audio amplifier from the vehicle. Hope this helps, good luck.
Rick McAninch, you did not give us a lot of information about which year your Yukon is or which amp. I assume it has the Bose system. Check under the rear seat on the drivers side. there should be a black box and you will need to remove the cover. Hope this helps, good luck.