Error Code (if any): F6E3, F7E7, F7E4, F7E3
Parts or tests already tried:

1. I tried replacing the actuator
   1. Similar situation: would not fill, would not spin
   2. However, new actuator did allow the cycle to run the duration rather than jump to complete
2. I checked the clutch assembly
   1. no signs of wear, plastic teeth look good
3. Checked the stator for continuity, and had resistance on its pins at the harness
4. Checked the wires from the board to the stator, and those tested fine
5. the water/fill/pressure tube has no blockage in it, it’s clear
6. I can manually spin the basket/drum with no issues
   1. nothing is impeding it from spinning
7. The rotor spins smoothly, clogging to magnets of course.
8. the magnets on the stator are fine as well.
9. When I run the diagnostic mode:
   1. water fills
   2. drains
   3. basket does not move at all

⟐ Commented June 08, 2026 at 15:08 MST

⟐ Commented June 08, 2026 at 11:51 MST

⟐ Answered June 07, 2026 at 7:38 MST

⟐ Answered June 06, 2026 at 1:26 MST

⟐ Answered June 05, 2026 at 17:10 MST

⟐ Answered June 04, 2026 at 19:23 MST

⟐ Answer accepted June 03, 2026 at 21:50 MST

My grandpa has a Miele w5801 washer, it recently stopped filling water.

It returns a water supply error.

I cleaned the filter at the inlet with little result. I can hear the relays click that are supposed to open the supply solenoid, but no water actually comes in.

Could this be a solenoid issue? If yes, what part number should I look for? Or is there another place I should check first?

Thank you in advance!

⟐ Commented June 03, 2026 at 14:37 MST

⟐ Commented June 01, 2026 at 21:29 MST

My washer fills up with water but the agitator won't work

⟐ Edited by author May 29, 2026 at 14:41 MST

⟐ Commented May 29, 2026 at 10:18 MST

⟐ Commented May 29, 2026 at 0:59 MST

My washing machine has an issue where it pours water during the spin cycle, while it is draining. Basically, it pours water from the top while draining it out from the bottom. It drains the water faster than it can pour it, so it does not actually fill with water, but it does re-wet the clothes, so the clothes are dripping wet when the cycle is complete.

It also agitates while filling with water. This is not much of a problem, but it started happening the same time that the other issue above started happening.

Model: Kenmore Elite 26964503

This is what the washing machine is supposed to do:

1. Wash Cycle
   1. Fill with water.
   2. When full, begin agitating.
   3. After a while, drain water.
2. Rinse Cycle
   1. Fill with water.
   2. When full, begin agitating.
   3. After a while, drain water.
3. Spin Cycle
   1. Spin while draining water.
   2. When empty, continue spinning and draining.
   3. After a while, stop.

This is what the washing machine actually does (the bold text marks the differences):

1. Wash Cycle
   1. Fill with water while agitating.
   2. When full, continue agitating.
   3. After a while, drain water.
2. Rinse Cycle
   1. Fill with water while agitating.
   2. When full, continue agitating.
   3. After a while, drain water.
3. Spin Cycle
   1. Spin while draining water.
   2. When empty, continue spinning and draining but also begin pouring water from top.
   3. After a while, stop.

The main problem is 3-2: in the spin cycle, the machine begins to pour water after it has drained all of the water. It is not supposed to be pouring water at this point; it defeats the purpose of the spin cycle.

What could this be? What would cause it to pour water during the spin cycle?

⟐ Answered May 28, 2026 at 9:47 MST

⟐ Commented May 25, 2026 at 8:04 MST

⟐ Commented May 24, 2026 at 8:53 MST