if its turned on the battery also doesn't go higher than 1%

⟐ Commented maio 23, 2026 at 2:39 GMT-7

⟐ Answer edited maio 17, 2026 at 8:35 GMT-7

How can I unstuck the merely stuck power button?

⟐ Answered maio 16, 2026 at 8:32 GMT-7

⟐ Answer accepted maio 14, 2026 at 0:23 GMT-7

⟐ Commented maio 14, 2026 at 0:00 GMT-7

Any help on fixing the glass I can’t find any guides for it?

⟐ Answered maio 10, 2026 at 0:22 GMT-7

⟐ Answered maio 09, 2026 at 16:40 GMT-7

⟐ Answer unaccepted maio 08, 2026 at 20:35 GMT-7

I replaced the battery of my iPad 2 with the new iFixit one but now it is stuck in a boot loop. I tried my old battery and it shows a low battery sign but the new battery just puts the iPad in boot loop. I tried the Home button + power button reboot thing but it didn't work. Could it be that the new battery might be faulty?

Thanks for any help :)

⟐ Commented maio 07, 2026 at 11:49 GMT-7

Could you help me out and provide advice please ?

Thanks

⟐ Answered maio 05, 2026 at 7:56 GMT-7

Could you you provide me some advice please ?

Thanks

⟐ Answered abril 20, 2026 at 5:18 GMT-7

⟐ Answer accepted abril 19, 2026 at 10:53 GMT-7

The sound on my iPad all of a sudden stopped working. The sound works fine with headphones in and I can change the volume, but when I unplug the headphones I get absolutely no sound from the speaker, and I can't even change the volume.

I originally thought this must have been a software issue so I went through all the settings, checked mute etc.

After that, I tried a reset using the power and home button, and I even restored to factory settings.

I then changed the speaker with a new one, still no luck.

I have now changed the headphone jack as I thought this may have been interfering, but there is still no sound.

Any help would be very much appreciated!!!

Thanks,

Michael

⟐ Commented abril 17, 2026 at 17:27 GMT-7

⟐ Answered abril 16, 2026 at 21:34 GMT-7

I replaced the battery but still getting the TG0B error. The battery level is fluctuating as well. I checked the capacitor C8923 and I got diode resistanc f .883 not sure if this is too high. FL8900 is good as well. What Iam not sure is the Q8900 which for BATT_SWI_FL.

The C8922 which is for BATT_NTC is ok as well it go straight to PMU chip. I tried to jump a wire from the battery terminal directly to batt_ntc n C8922 in case the connection going to the battery is loose but still getting TG0B ... This issue is a pain.

⟐ Answered abril 15, 2026 at 9:16 GMT-7

Reboots are not spaced evenly at 180s apart, which probably indicates the sensor is responsive at times and not at others? At the beginning of the issue, I could sometimes use it for 5-10 minutes without rebooting, and sometimes less. Charge level fluctuates around 10-20% on each reboot and just randomly when unlocked. The reboots got more frequent and regular over time. Last night it seemed the iPad was charging very slow.

I took it for repair today,

They replaced the battery and the issue persists.

I've read TG0B is an NTC thermistor in the battery.... what could be the next steps? Any possible issues in the measurement circuitry?

panic(cpu 0 caller 0xfffffff0243a0514): userspace watchdog timeout: no successful checkins from thermalmonitord
service returned not alive with context : is_alive_func returned unhealthy : current 1ffffffe, mask 1fffffff, expected 1fffffff. EC: 1 EH: 3758097110 3758097110 SD: 0 BC: 0 RC: -1 BS: 0, Missing sensor(s): TG0B

⟐ Commented abril 15, 2026 at 9:11 GMT-7

I got an iPad 9th gen WiFi battery replacement kit. I tried using iopener multiple times as instructed. I even used a blow dryer directed the heat towards the display in a blanket. The display didnt budge at all!

Is it possible to use the adhesive remover that came with the kit and put it along the display? Is there anything i should know about this? like would it ruin the device or the display if i am still unable to open the display?

⟐ Commented abril 11, 2026 at 13:17 GMT-7